Ibywind Screen Protector For OnePlus 8T[2 Pack],9H Hardness Tempered Glass,With 1Pc Camera Lens Protector,1Pc Back Carbon Fiber Film(Not for OnePlus 8/OnePlus 8 Pro)

Top Tier Protection
What happened to screen protectors? It used to be that you would get a screen protector in a little package, stickied to a flimsy piece of paper, and the instructions were simply “Remove from film and apply. You may need to use a credit card to work out any bubbles.”Now screen protectors feel like they come with 3D printers and an operation manual to apply.I felt like that when I received this, but quickly realized it was for good reason. This is a REALLY good screen protector, and it’s much easier and more efficient to apply than any other I’ve used.It comes in a nice case, you get all the tools you need, clear instructions, a simple video, and the end product is fantastic. I was intimidated by the process on first look, but in reality it’s very simple and very good. No bubbles, no fuss, and the bonus back protector was a nice touch! I have the One Plus 5G UW with the center back camera and left-positioned from camera and it works perfectly.Feels like the seller put some care and genuine thought into this one.

I made Better Instructions (no bubbles) + Pros and Cons
Summary: Great product, Bad/Missing instructionsI WROTE BETTER INSTRUCTIONS later in my comment.PROs: easier to install than most and better instructions than most, no bubbles if installed carefully (see my instructions), clever alignment tool, screen protector is smooth/slippery and doesn’t feel rubbery, my Case (spigen ultra hybrid) didn’t interfere/pop off the screen protector, fingerprint reader works well (once re-settup), smudges less than others I’ve used (hand oils), rear and camera protectors are a nice bonus.CONs: instructions aren’t amazing (could be worse), Only 2 screen protectors :(, only 1 camera protector and it’s plastic :(, only 1 back protector that doesn’t go all the way to the edge and the carbon patern is a bit ugly :(.PROPER INSTRUCTIONS (so you don’t get bubbles) :SCREEN:(1) Dust Is Your Enemy! Find a Clean and Bright space! (Examples: Kitchen counter/table, Bathroom Counter, Desk with lamp). Moving air stirs up dust so Turn off any fans in the room for a couple minutes and let the dust settle. Wipe down your work area (table) with a damp cloth (Just Water, cotton t-shirts work best)(2) Take of your case and Wipe down all sides of the phone with that damp cloth to get it clean, also wash your hands.(3) Insert the alignment tool (plastic positioner) into the charge port all the way, prongs on the screen side (you need to push pretty hard)(4) Set the phone down on the Rubber pad(5) Grab the accessories: Alcohol Wipe (no. 1) and Microfiber Cloth (no. 2), ignore the sticker(6) Wipe the screen with the Alcohol wipe Without unfolding it, and go over it a few times (save the wipe for the back and lens protectors).(7) Dry/Polish the screen with the microfiber cloth making sure to polish the whole screen until streaks go away(8) fold the cloth and wipe in straight lines from bottom to top away from the alignment tool to remove dust(9) check the screen is clean without touching the phone (look at the screen from the side of the phone/have your head at the edge of the table) If dusty repeat 8(10) Grab Screen protector, attach it to the alignment tool and set it on screen(11) Lightly pull on the tab at the top of the screen protector and use the Squeegee to Gently wipe from the bottom of the screen protector to the top to align the protector(12) Follow the instructions they sent starting with “Step 8″(13) Use the squeegee to gently push any bubbles towards edge of screen protector(14) Use the microfiber cloth to gently but firmly press down the edges of the screen protector always wiping from the middle of the screen to the edge.CAMERA Protector:(1) Find a clean working space (Screen Step 1)(2) Find and grab camera protector, it is on a small piece of black plastic, do not remove plastic protector(3) Wipe the Camera Lense glass with the Alcohol wipe you used for the screen(4) Dry/polish the camera glass with the microfiber(5) Grab the sticker from the accessories pack and stick it to the camera firmly then remove it.(6) Remove the lense protector from the black plastic piece. bend the black plastic using the 2 tabs until the lense protector partially releases, then lift it the rest of the way off by lifting by the clear film.(7) Holding the lense protector by the clear film, line up the protector with the lense and press firmly.(8) Remove the plastic film and you are done.BACK Protector:(1) Find a clean working space (Screen Step 1)(2) Find and grab Back protector, and discard the small piece (it is just left over from making the camera/flash hole)(3) set down the phone on the rubber mat, and Wipe the Back Glass with the Alcohol wipe you used for the screen and camera lense(4) Dry/polish the back glass with the microfiber(5) Check to make sure the back glass is dust free(6) Peel the paper back halfway (peel the top), line up the camera with the hole (make sure its straight and even) then stick down around the camera.(7) Peel the the rest of the paper backing and stick the lower half of the protector (if it is not straight carefully partially peel up and re-stick)(8) Use the squeegee to press down the back protector and to remove air bubbles (if ii has bubbles carefully peel up and press back down with squeegee)(9)Use the microfiber cloth to gently press down the edges of the protector always wiping from the middle to the edgeAdmire your work 🙂

Ok so 10 minutes in and this seems to be a premium product. The end result is flawless, almost like having no protector on at all. The touch experience is smooth, the only problem is the on-screen fingerprint detection which takes longer to register now. Certainly for unlocking, you have to keep your finger on the screen for a good 2 seconds whereas without it was instant. Providing bio info for apps seems better though. It’s only a minor niggle. The provided instructions were clear and the kit easy to use. The provided frame guide for my OnePlus 8T was slightly too small and kept popping off but that was no problem, I only had to hold it down until I dropped the protector in place. Now for the bubbles. Like others have said you do end up with bubbles or patches that need rubbing clean and the only way seems to be to use the corner of a credit card wrapped in the polishing cloth and rubbing really hard. I ended up bending the corner of my card in the end I was putting so much pressure on but you really do need to disperse the bubbles or patches underneath until they fade away. 5 minutes elbow grease though and result is amazing. Happy so far and I have a spare just in case.There is an additional protector for the camera glass on the back too and also provided is a neat carbon fibre effect film for the entire back. I’m not sure how long this will last because it does wrap up the edges a little bit but it does afford additional protection and means you don’t need a case. We’ll see how long it lasts but it’s good for now. (Edit. 4 days. It’s too flimsy and the corners lifted. No real loss)

المنتج خطير وسهل الاستخدام، يركب بالمليميتر وموجد له شرح في اليوتيوب من الشركة نفسها. جودة المنتج عاليه وفاق تصوراتي، الحماية الامامية شفافة جدا وتركيبها احترافي. وتجي معها حماية للوجه الخلفي وزجاج صغير للكاميرات. رائع رائع.

Una material bueno, recomendable para pantallas curvas, proteje bien la pantalla, además de que tiene un extra y su equipo para colocar bien el protector, lo recomiendo.