Ibywind Screen Protector For OnePlus 8T[2 Pack],9H Hardness Tempered Glass,With 1Pc Camera Lens Protector,1Pc Back Carbon Fiber Film(Not for OnePlus 8/OnePlus 8 Pro)

Fits perfectly, easy to install
Very good directions and easy to install. The only thing is there are no directions for the back side but I don’t need it anyway.

I made Better Instructions (no bubbles) + Pros and Cons
Summary: Great product, Bad/Missing instructionsI WROTE BETTER INSTRUCTIONS later in my comment.PROs: easier to install than most and better instructions than most, no bubbles if installed carefully (see my instructions), clever alignment tool, screen protector is smooth/slippery and doesn’t feel rubbery, my Case (spigen ultra hybrid) didn’t interfere/pop off the screen protector, fingerprint reader works well (once re-settup), smudges less than others I’ve used (hand oils), rear and camera protectors are a nice bonus.CONs: instructions aren’t amazing (could be worse), Only 2 screen protectors :(, only 1 camera protector and it’s plastic :(, only 1 back protector that doesn’t go all the way to the edge and the carbon patern is a bit ugly :(.PROPER INSTRUCTIONS (so you don’t get bubbles) :SCREEN:(1) Dust Is Your Enemy! Find a Clean and Bright space! (Examples: Kitchen counter/table, Bathroom Counter, Desk with lamp). Moving air stirs up dust so Turn off any fans in the room for a couple minutes and let the dust settle. Wipe down your work area (table) with a damp cloth (Just Water, cotton t-shirts work best)(2) Take of your case and Wipe down all sides of the phone with that damp cloth to get it clean, also wash your hands.(3) Insert the alignment tool (plastic positioner) into the charge port all the way, prongs on the screen side (you need to push pretty hard)(4) Set the phone down on the Rubber pad(5) Grab the accessories: Alcohol Wipe (no. 1) and Microfiber Cloth (no. 2), ignore the sticker(6) Wipe the screen with the Alcohol wipe Without unfolding it, and go over it a few times (save the wipe for the back and lens protectors).(7) Dry/Polish the screen with the microfiber cloth making sure to polish the whole screen until streaks go away(8) fold the cloth and wipe in straight lines from bottom to top away from the alignment tool to remove dust(9) check the screen is clean without touching the phone (look at the screen from the side of the phone/have your head at the edge of the table) If dusty repeat 8(10) Grab Screen protector, attach it to the alignment tool and set it on screen(11) Lightly pull on the tab at the top of the screen protector and use the Squeegee to Gently wipe from the bottom of the screen protector to the top to align the protector(12) Follow the instructions they sent starting with “Step 8″(13) Use the squeegee to gently push any bubbles towards edge of screen protector(14) Use the microfiber cloth to gently but firmly press down the edges of the screen protector always wiping from the middle of the screen to the edge.CAMERA Protector:(1) Find a clean working space (Screen Step 1)(2) Find and grab camera protector, it is on a small piece of black plastic, do not remove plastic protector(3) Wipe the Camera Lense glass with the Alcohol wipe you used for the screen(4) Dry/polish the camera glass with the microfiber(5) Grab the sticker from the accessories pack and stick it to the camera firmly then remove it.(6) Remove the lense protector from the black plastic piece. bend the black plastic using the 2 tabs until the lense protector partially releases, then lift it the rest of the way off by lifting by the clear film.(7) Holding the lense protector by the clear film, line up the protector with the lense and press firmly.(8) Remove the plastic film and you are done.BACK Protector:(1) Find a clean working space (Screen Step 1)(2) Find and grab Back protector, and discard the small piece (it is just left over from making the camera/flash hole)(3) set down the phone on the rubber mat, and Wipe the Back Glass with the Alcohol wipe you used for the screen and camera lense(4) Dry/polish the back glass with the microfiber(5) Check to make sure the back glass is dust free(6) Peel the paper back halfway (peel the top), line up the camera with the hole (make sure its straight and even) then stick down around the camera.(7) Peel the the rest of the paper backing and stick the lower half of the protector (if it is not straight carefully partially peel up and re-stick)(8) Use the squeegee to press down the back protector and to remove air bubbles (if ii has bubbles carefully peel up and press back down with squeegee)(9)Use the microfiber cloth to gently press down the edges of the protector always wiping from the middle to the edgeAdmire your work 🙂

Cheap & Great Screen Protector
The installation of the screen protector was really easy with the plastic frame that was included to help fit it. The screen protector fits perfectly with the phone and there aren’t any problems with bubbles or dust. The only negative thing I found with it is that the fingerprint sensor works a little bit slower than when I didn’t have it on. There was also a camera protector and a carbon fiber printed sticker which was pretty cool. The camera lens protector didn’t really work that well and was pretty hard to fit. The carbon fiber sticker was also pretty hard to apply, but when I got it right after a few tries. It makes makes your phone look really awesome and eliminates finger prints on the back glass.

Ok so 10 minutes in and this seems to be a premium product. The end result is flawless, almost like having no protector on at all. The touch experience is smooth, the only problem is the on-screen fingerprint detection which takes longer to register now. Certainly for unlocking, you have to keep your finger on the screen for a good 2 seconds whereas without it was instant. Providing bio info for apps seems better though. It’s only a minor niggle. The provided instructions were clear and the kit easy to use. The provided frame guide for my OnePlus 8T was slightly too small and kept popping off but that was no problem, I only had to hold it down until I dropped the protector in place. Now for the bubbles. Like others have said you do end up with bubbles or patches that need rubbing clean and the only way seems to be to use the corner of a credit card wrapped in the polishing cloth and rubbing really hard. I ended up bending the corner of my card in the end I was putting so much pressure on but you really do need to disperse the bubbles or patches underneath until they fade away. 5 minutes elbow grease though and result is amazing. Happy so far and I have a spare just in case.There is an additional protector for the camera glass on the back too and also provided is a neat carbon fibre effect film for the entire back. I’m not sure how long this will last because it does wrap up the edges a little bit but it does afford additional protection and means you don’t need a case. We’ll see how long it lasts but it’s good for now. (Edit. 4 days. It’s too flimsy and the corners lifted. No real loss)

Very easy install and seems good quality. Good price too!

Anfangs war ich aufgrund der negativen Rezensionen skeptisch. Nach langem hin und her überlegen, habe ich mich doch dafür entschieden. Die Folie ist für mein OnePlus 8T, der leider gefallen ist und das Display etwas gerissen war. Um eine Verschlimmerung entgegenzuwirken, habe ich die Schutzfolie bestellt.Da ich schon in mehreren Geräten solche Folien anbringen konnte, war es für mich nichts Neues.Die Schutzpanzer-Folie (wenn es tatsächlich als Schutzpanzer deklariert werden kann) hat eine gute Qualität und macht einen robusten Eindruck. Für das Anbringen hat der Hersteller alles Notwendige dazu geliefert.Es gibt die Folie, ein Abstandshalter (damit die richtig mittig positioniert werden kann, ein feuchtes Reinigungstuch, ein hochwertiges Trockentuch (was auch später weiter verwendet werden kann), auf Aufkleber um kleine Staubkörner danach zu entfernen. Dazu gibt es noch eine Schutzfolie für das Kamera-Modul (was ich nicht genutzt habe), eine Tube mit Öl um gegebenenfalls die Schutzfolie seitlich an das Handy festzumachen (wenn es notwendig sein sollte, was bei mir nicht der Fall war) und eine Aufkleber-Schutzfolie für die Rückseite des Geräts (transparent mit Kevlar-Muster und restlos wieder entfernbar). Die Schutzfolie für die Rückseite sehe ich eher als Gimmick an, da es lediglich Schutz vor kleinere Kratzer bietet.Nun zu der eigentlichen Display-Schutzfolie. Selten konnte ich eine Schutzfolie so einfach anbringen! So easy, einfach und schnell, da war ich baff. Das Zentrieren ging ganz leicht und nach einem kurzen Fingerdruck in der Mitte, setzt sich die Folie wie von selbst und beginnt sich “anzuhaften”. Auch ohne den mitgelieferten Öl steht keine einzige Ecke der Folie hoch und schließt nicht bündig. Dass die Folie etwas kleiner als mein Display ist, halte ich für normal, andernfalls könnte ich mein Cover für die Rückseite nicht anbringen.Bei der Benutzung empfinde ich die Folienkanten nicht als scharf, sondern angenehm wie als leicht abgerundet. Der Finger gleitet angenehm darüber.Und eine Folie habe ich für den Fall eines Falles noch als Reserve. Zuerst war ich wegen des Preises skeptisch, jetzt sage ich: “Ist das Geld auf jeden Fall wert!”. Die Anbringung ist easy, viel Zubehör, gute Qualität und macht das Leben etwas leichter (anstatt mich mit der Anbringung ärgern zu müssen).